| Doc # |
Name |
Stage/Close Date |
| Connectors |
|
AWI 6164
|
Four-screw, one-piece square-flange connectors for use at 25 and 40 MPa (revision of ISO 6164:1994)
|
Systematic review resulted in decision to revise this International Standard.
|
| AWI 7241 |
Hydraulic quick-action coupling dimensions and requirements [revision and renumbering of ISO 7241-1:1987]
|
New work item proposal approved.
|
| Approved work item |
Hydraulic quick-action coupling test methods [revision and renumbering of ISO 7241-2:2000] |
New work item proposal approved. |
| AWI 14540 |
Dimensions and requirements for hydraulic screw-to-connect quick-action couplings for high pressure fluid power applications |
New work item proposal approved. |
| AWI 14541 |
Dimensions and requirements for hydraulic screw-to-connect quick-action couplings for general purpose |
New work item proposal approved. |
| ISO 6149-1:2006 |
Ports with ISO 261 threads and O-ring sealing |
International Standard confirmed until 2014. |
| ISO 6149-2:2006 |
Heavy-duty stud ends for ports with ISO 261 threads and O-ring sealing |
International Standard confirmed until 2014. |
| ISO 6149-3:2006 |
Light-duty stud ends for ports with ISO 261 threads and O-ring sealing |
International Standard confirmed until 2014. |
| ISO 6149-4:2006 |
Plugs for ISO 6149-1 ports |
International Standard confirmed until 2014. |
| ISO 8434-3:2005 |
Metallic tube connections for fluid power and general use – Part 3: O-ring face seal connectors |
International Standard confirmed until 2013, and a technical corrigendum will be published. |
| ISO 9974-4:20 |
Plugs for ISO 9974-1 ports |
International Standard confirmed until 2014. |
| ISO 12151-2:2003 |
Hose fittings with ISO 8434-1 and ISO 8434-4 24º cone connector ends with O-rings |
International Standard confirmed until 2013. |
| ISO 15171-1:1999 |
Hydraulic couplings for diagnostic purposes – Part 1: Coupling not for connection under pressure |
International Standard confirmed until 2014, and a technical corrigendum will be published. |
| ISO 16028:1999 |
Hydraulic flush-face type, quick-action couplings for use at pressures of 20 MPa to 31,5 MPa |
International Standard was confirmed until 2014. |
| ISO 19879:2005 |
Test methods for hydraulic fluid power connectors |
International Standard confirmed until 2010, and a technical corrigendum will be published.
|
| Contamination control |
| FDIS 27407 |
Marking of filtration performance characteristics on hydraulic filters |
Final Draft International Standard circulated to U.S. TAG SC 6 for ballot, which closed 2010-03-10, and to NFPA/T3.10 for comments. |
| ISO 3938:1986 |
Method of reporting contamination analysis data |
International Standard confirmed until 2014. |
| ISO 4406:1999 |
Method for coding the level of contamination by solid particles in hydraulic fluids |
International Standard confirmed until 2014. |
| Cylinders |
| ISO 4393:1978 |
Basic series of cylinder piston strokes |
International Standard was confirmed until 2013. |
| ISO 6430:1992 |
Mounting dimensions for single-rod pneumatic cylinders with integral mountings with bores from 32 mm to 250 mm for use at 1000 kPa |
International Standard was confirmed until 2014. |
| Pumps and motors |
| ISO 4391:1983 |
Parameter definitions and letter symbols for hydraulic pumps, motors and integral transmissions |
Intentional Standard was confirmed until 2013. |
| ISO 10767-3:1999 |
Determination of pressure ripple levels generated in hydraulic motors |
International Standard confirmed until 2014. |
| Sealing devices |
| FDIS 5597 |
Dimensions and tolerances for housings for hydraulic cylinder piston and rod seals in reciprocating applications |
Final Draft International Standard circulated to U.S. TAG SCs 3 and 7 for ballot, which closes 2010-03-15, and to NFPA/T3.6 and T3.19 for comments. |
| |
|
|